
dsPIC33F

dsPIC DSC High-Performance 16-Bit
Digital Signal Controllers

Operating Range

 DC  40 MIPS (40 MIPS @ 3.0-3.6V, -40 to +85C)
 Industrial temperature range (-40 to +85C)

High-Performance DSC CPU

 Modified Harvard architecture
 C compiler optimized instruction set
 16-bit wide data path
 24-bit wide instructions
 Linear program memory addressing up to 4M
  instruction words
 Linear data memory addressing up to 64 Kbytes
 84 base instructions: mostly 1 word/1 cycle
 Sixteen 16-bit general purpose registers
 Two 40-bit accumulators:
  - With rounding and saturation options
 Flexible and powerful addressing modes:
  - Indirect, modulo and bit-reversed
 Software stack
 16 x 16 fractional/integer multiply operations
 32/16 and 16/16 divide operations
 Single-cycle multiply-and-accumulate:
  - Accumulator write back for DSP operations
  - Dual data fetch
 Up to +/- 16-bit shifts, for up to 40-bit data
  Direct Memory Access (DMA)
 8-channel hardware DMA
 Allows data transfer between RAM and a
  peripheral while CPU is executing code (no cycle
  stealing)
 2 KB of dual-ported DMA buffer area (DMA RAM)
  to store data transferred via DMA
 Most peripherals support DMA

Interrupt Controller

 5-cycle latency
 117 interrupt vectors
 Up to 67 available interrupt sources, up to
  5 external interrupts
 7 programmable priority levels
 5 processor exceptions

Digital I/O

 Up to 85 programmable digital I/O pins
 Wake-up/Interrupt-on-Change on up to 24 pins
 Output pins can drive from 3.0V to 3.6V
 All digital input pins are 5V tolerant
 4 mA sink and source on all I/O pins

On-Chip Flash and SRAM

 Flash program memory, up to 256 Kbytes
 Data SRAM (up to 30 Kbytes):
  - Includes 2 KB of DMA RAM

System Management

 Flexible clock options:
  - External, crystal, resonator, internal RC
  - Fully integrated PLL
  - Extremely low jitter PLL
 Power-up timer
 Oscillator Start-up Timer/Stabilizer
 Watchdog timer with its own RC oscillator
 Fail-Safe Clock Monitor
 Reset by multiple sources

Power Management

 On-chip 2.5V voltage regulator
 Switch between clock sources in real time
 Idle, Sleep and Doze modes with fast wake-up

Timers/Capture/Compare/PWM

 Timer/Counters: up to nine 16-bit timers:
  - Can pair up to make four 32-bit timers
  - 1 timer runs as Real-Time Clock with external
    32 kHz oscillator
  - Programmable prescaler
 Input Capture (up to 8 channels):
  - Capture on up, down or both edges
  - 16-bit capture input functions
  - 4-deep FIFO on each capture
 Output Compare (up to 8 channels):
  - Single or Dual 16-Bit Compare mode
  - 16-Bit Glitchless PWM mode


Communication Modules

 3-wire SPI (up to 2 modules):
  - Framing supports I/O interface to simple
    codecs
  - Supports 8-bit and 16-bit data
  - Supports all serial clock formats and
    sampling modes
  - 8-word FIFO buffers
 I2C (up to 2 modules):
  - Full Multi-Master Slave mode support
  - 7-bit and 10-bit addressing
  - Bus collision detection and arbitration
  - Integrated signal conditioning
  - Address masking
 UART (up to 2 modules):
  - Interrupt-on-address bit detect
  - Wake-up-on-Start bit from Sleep mode
  - 4-character TX and RX FIFO buffers
  - LIN bus support
  - IrDA encoding and decoding in hardware
  - High-Speed Baud mode
 Data Conversion Interface (DCI) module:
  - Codec interface
  - Supports I2S and AC97 protocols
  - Up to 16-bit data words, up to 16 words per
    frame
  - 4-word deep TX and RX buffers
 Enhanced CAN 2.0B active (up to 2 modules):
  - Up to 8 transmit and up to 16 receive buffers
  - 16 receive filters and 3 masks
  - Loopback, Listen Only and Listen All
    Messages modes for diagnostics and bus
    monitoring
  - Wake-up on CAN message
  - FIFO mode using DMA

Motor Control Peripherals

 Motor Control PWM (up to 8 channels):
  - 4 duty cycle generators
  - Independent or Complementary mode
  - Programmable dead time and output polarity
  - Edge or center-aligned
  - Manual output override control
  - Up to 2 Fault inputs
  - Trigger for A/D conversions
  - PWM frequency for 16-bit resolution
    (@ 40 MIPS) = 1220 Hz for Edge-Aligned
    mode, 610 Hz for Center-Aligned mode
  - PWM frequency for 11-bit resolution
    (@ 40 MIPS) = 39.1 kHz for Edge-Aligned
    mode, 19.55 kHz for Center-Aligned mode
 Quadrature Encoder Interface module:
  - Phase A, Phase B and index pulse input
  - 16-bit up/down position counter
  - Count direction status
  - Position Measurement (x2 and x4) mode
  - Programmable digital noise filters on inputs
  - Alternate 16-bit Timer/Counter mode
  - Interrupt on position counter rollover/
    underflow

Analog-to-Digital Converters

 Up to two 10-bit or 12-bit A/D modules in a device
 10-bit 2.2 Msps or 12-bit 1 Msps conversion:
  - 2 or 4 simultaneous samples
  - Up to 32 input channels with auto-scanning
  - 16-deep result buffer
  - Conversion start can be manual or
    synchronized with 1 of 4 trigger sources
  - Conversion possible in Sleep mode
  - 1 LSB max integral nonlinearity
  - 1 LSB max differential nonlinearity

CMOS Flash Technology

 Low-power, high-speed Flash technology
 Fully static design
 3.3V (+/- 10%) operating voltage
 Industrial temperature
 Low-power consumption
  
Packaging:

 100-pin TQFP (14x14x1 mm and 12x12x1 mm)
 80-pin TQFP (12x12x1 mm)
 64-pin TQFP (10x10x1 mm)


